Hi All, I am a student at the University of New Hampshire, attempting to continue work on the true muonium section of the HPS experiment. I am looking to run true muonium data through the simulation software and then analyze the reconstructed tracks. I have successfully used the software in the past, but am currently running into an error with readout simulation that I have never encountered. I am using hps-distribution-3.0.0-bin.jar, which I believe is the latest stable release, with detector HPS-Proposal2014-v5-6pt6 and a true muonium data file that was created by assuming the same decay properties as the heavy photon, except with a mass of 211 MeV. Below is the command that I am using to run readout simulation and the error I receive. Is this error familiar to anyone? Thank you for any help. Regards, Chad Civello [ccivello@taro Out_files]$ java -jar hps-distribution.jar -r /org/lcsim/hps/steering/readout/HPS2014ReadoutNoPileup.lcsim -i TM_6786MeV_Fall2013_HPS-Proposal2014-v5-6pt6.slcio -DoutputFile=TM_6786MeV_Fall2013_HPS-Proposal2014-v5-6pt6_readout --- Drivers --- org.lcsim.job.EventMarkerDriver eventInterval = 1000 org.lcsim.hps.conditions.CalibrationDriver org.lcsim.hps.recon.ecal.EcalEdepToTriggerConverterDriver readoutCollection = EcalReadoutAnalogHits applyBadCrystalMap = false truncateScale = 1 constantGain = 0.15 org.lcsim.hps.recon.ecal.EcalRawConverterDriver runBackwards = true rawCollectionName = EcalReadoutHits ecalCollectionName = EcalReadoutAnalogHits org.lcsim.hps.recon.ecal.CTPEcalClusterer ecalName = Ecal ecalCollectionName = EcalReadoutAnalogHits clusterCollectionName = EcalTriggerClusters org.lcsim.hps.readout.ecal.FADCTriggerDriver clusterCollectionName = EcalTriggerClusters outputFileName = TM_6786MeV_Fall2013_HPS-Proposal2014-v5-6pt6_readout.triggers deadTime = 0 lcioFile = TM_6786MeV_Fall2013_HPS-Proposal2014-v5-6pt6_readout.slcio org.lcsim.hps.recon.tracking.SimpleSvtReadout noPileup = true org.lcsim.hps.util.ClockDriver org.lcsim.recon.tracking.digitization.sisim.config.ReadoutCleanupDriver --- End Drivers --- No input files in XML file. Got ConditionsEvent with run: 0 Reading calibrations calibSVT/base for run: 0 Use this calibration from run -1: calibSVT/default.base Reading calibrations calibSVT/tp for run: 0 Use this calibration from run -1: calibSVT/default.tp Loading the SVT bad channels for run 0 File daqmap/svt0.badchannels was not found! Continuing with only QA bad channels Loading SVT gains ... Loading SVT t0 shifts ... Loading fieldmap for run 0 reading ECal DAQ map reading ECal bad channels reading pedestals for ECal reading pedestals for ECal FADCTriggerDriver: Setting trigger for 6.6 GeV beam >> Event 0 java.lang.RuntimeException: Distance is outside of sensor by more than 0.001. Distance = -0.24857335945534142. If this is an isolated event, then perhaps DISTANCE_ERROR_THRESHOLD must be increased in CDFSiSensorSim at org.lcsim.recon.tracking.digitization.sisim.CDFSiSensorSim.diffusionDistribution(CDFSiSensorSim.java:478) at org.lcsim.recon.tracking.digitization.sisim.CDFSiSensorSim.depositChargeOnSense(CDFSiSensorSim.java:241) at org.lcsim.recon.tracking.digitization.sisim.CDFSiSensorSim.computeElectrodeData(CDFSiSensorSim.java:110) at org.lcsim.hps.recon.tracking.SimpleSvtReadout.doSiSimulation(SimpleSvtReadout.java:198) at org.lcsim.hps.recon.tracking.SimpleSvtReadout.process(SimpleSvtReadout.java:116) at org.lcsim.util.Driver.doProcess(Driver.java:273) at org.lcsim.util.Driver.processChildren(Driver.java:284) at org.lcsim.util.Driver.process(Driver.java:198) at org.lcsim.util.DriverAdapter.recordSupplied(DriverAdapter.java:74) at org.freehep.record.loop.DefaultRecordLoop.consumeRecord(DefaultRecordLoop.java:832) at org.freehep.record.loop.DefaultRecordLoop.loop(DefaultRecordLoop.java:668) at org.freehep.record.loop.DefaultRecordLoop.execute(DefaultRecordLoop.java:566) at org.lcsim.util.loop.LCSimLoop.loop(LCSimLoop.java:153) at org.lcsim.job.JobControlManager.run(JobControlManager.java:392) at org.lcsim.job.JobControlManager.main(JobControlManager.java:168) ######################################################################## Use REPLY-ALL to reply to list To unsubscribe from the HPS-SOFTWARE list, click the following link: https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1