 |
 |
Alessandra, did you solve your problem? I think Jeremy added a fix for this? On Jan 21, 2015, at 9:01 PM, Graham, Mathew Thomas <[log in to unmask]> wrote: > > Actually, I can’t seem to connect to the DB at all from where I am (Fermilab). I think FNAL has SLAC cut off, somehow; they’ve always been jealous of us..I can’t get to the svn repository either. Here’s the log file for those interested: > <foobar> > > > > On Jan 21, 2015, at 10:38 PM, Graham, Mathew Thomas <[log in to unmask]> wrote: > >> So there are definitely TrackerHits in your slcio file…it looks fine to me. I’ll try running some readout. >> >> >> On Jan 21, 2015, at 10:23 AM, Alessandra Filippi <[log in to unmask]> wrote: >> >>> hi, >>> you can find the ap2* slcio it here: >>> >>> /nfs/slac/g/hps3/users/afilippi/hps/SCRATCH/OUT2014_v0/ap2.2gev075mev_all.slcio >>> >>> can you try to see if you can read it properly? (and there's something in?) >>> thanks! >>> >>> >>> >>> On Wed, 21 Jan 2015, Hansson Adrian, Per Ola wrote: >>> >>>> Hi, >>>> >>>> can you point us to the slcio file? >>>> >>>> On Jan 21, 2015, at 7:30 AM, Alessandra Filippi <[log in to unmask]> wrote: >>>> >>>>> Hi all, >>>>> sorry for the stupid question, but I am not able to get any result in running readout simulations, whichever steering lcsim file I use, and I need some help to get going. >>>>> I produced a .slcio file with slic on two kinds of stdhep files (ap2.2gev075mev* and Takashi's new brems-mad1.92gev*), using the slic installation at slac (old, but working - I think). I am using the HPSTestRunTracker2014-v0.lcdd geometry file. >>>>> Then, I try to produce a readout file, using the instructions in the >>>>> confluence "Running Readout Simulation" page (lcsim and hps_trunk >>>>> freshly updated). All I get, with both the .slcio files and whichever HPS2014Readout*.lcsim file, is the geometry survey of SVT (I guess), >>>>> and nothing else: the reconstruction ends with Ecal/svt setup info >>>>> >>>>> Wed Jan 21 16:19:15 CET 2015 :: EcalDetectorSetup :: INFO :: loading ECAL conditions onto subdetector Ecal >>>>> Wed Jan 21 16:19:15 CET 2015 :: EcalDetectorSetup :: INFO :: building ECAL geometry channel map >>>>> Wed Jan 21 16:19:15 CET 2015 :: EcalDetectorSetup :: INFO :: built ECAL geometry channel with 442 entries >>>>> Wed Jan 21 16:19:15 CET 2015 :: EcalDetectorSetup :: INFO :: done loading ECAL conditions onto subdetector >>>>> Wed Jan 21 16:19:26 CET 2015 :: SvtDetectorSetup :: INFO :: loading SVT conditions onto subdetector Tracker >>>>> Wed Jan 21 16:19:26 CET 2015 :: SvtDetectorSetup :: INFO :: setting up 20 SVT sensors >>>>> Wed Jan 21 16:19:26 CET 2015 :: SvtDetectorSetup :: INFO :: channel map has 23040 entries >>>>> End of file reached >>>>> Wed Jan 21 16:19:26 CET 2015 :: DatabaseConditionsManager :: INFO :: connection closed >>>>> >>>>> and the readout file is empty. >>>>> If I use HPSTrackingDefaults.lcsim, again on whichever kind of slcio file, after the drivers being loaded, I get >>>>> >>>>> Executed dry run. No events processed! >>>>> >>>>> and again nothing else is done. What am I doing wrong? >>>>> Thanks, cheers >>>>> Alessandra >>>>> >>>>> ps. I wanted to inspect the slcio files to see whether they had problems, but I cannot install JAS3 for the issue mentioned in my previous e-mail. >>>>> >>>>> ######################################################################## >>>>> Use REPLY-ALL to reply to list >>>>> >>>>> To unsubscribe from the HPS-SOFTWARE list, click the following link: >>>>> https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1 >>>> >>>> ######################################################################## >>>> Use REPLY-ALL to reply to list >>>> >>>> To unsubscribe from the HPS-SOFTWARE list, click the following link: >>>> https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1 >>>> >>> >>> ######################################################################## >>> Use REPLY-ALL to reply to list >>> >>> To unsubscribe from the HPS-SOFTWARE list, click the following link: >>> https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1 >> >> ######################################################################## >> Use REPLY-ALL to reply to list >> >> To unsubscribe from the HPS-SOFTWARE list, click the following link: >> https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1 > ######################################################################## Use REPLY-ALL to reply to list To unsubscribe from the HPS-SOFTWARE list, click the following link: https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1