 |
 |
Hi Everyone, All 1.5 and 0.5 mm runs have now been processed in pass1, ~3.5K files. Success rate for slcio and dst based on counting outputs looks very high. Unless anyone disagrees, I will start cleanup with finding failed jobs before bothering with anything above 1.5 mm. Or does anyone even care about the early runs with SVT > 1.5mm? https://confluence.slac.stanford.edu/display/hpsg/2015+EngRun+Reconstruction+Passes -Nathan On Jun 9, 2015, at 8:03 PM, Nathan Baltzell <[log in to unmask]> wrote: > Hi All, > > All calibration runs are now processed and their outputs on disk. > The canonical run 5772 is still being processed, and its lcio will end up on disk automatically. > It will be good if anyone can do a sanity check on it. > > I added to the list of canonical runs (i.e. those whose LCIO output will goto /work disk automatically > and permanently), since it is easier to do it now rather rather than get from tape later. They > looked reasonable on the run spreadsheet: 5698 and 5739 > > I will submit the remainder tonight/tomorrow unless I hear otherwise. > > -Nathan > > > > > > On Jun 9, 2015, at 11:48 AM, "Graf, Norman A." <[log in to unmask]> wrote: > >> Hi Nathan, >> Thanks. I saw them on tape, but didn't want to start staging the files >> independently. >> Norman >> >> -----Original Message----- >> From: Nathan Baltzell [mailto:[log in to unmask]] >> Sent: Tuesday, June 09, 2015 8:38 AM >> To: Graf, Norman A. >> Cc: hps-software >> Subject: Re: pass1 >> >> Hi Norman, >> >> They're on tape (you can see filesize in the stub files). I'm jgetting the calibration >> DSTs and LCIOs to the work disk (submission scripts weren't updated yet). >> >> -Nathan >> >> >> >> >> >> >> >> On Jun 9, 2015, at 11:11, Graf, Norman A. <[log in to unmask]> wrote: >> >>> Good Morning Nathan, >>> Thanks! What output lcio files are you looking at? >>> I'm not yet seeing any files on disk at >>> >>> /work/hallb/hps/data/engrun2015/pass1/recon/ >>> >>> Norman >>> >>> -----Original Message----- >>> From: [log in to unmask] >>> [mailto:[log in to unmask]] On Behalf Of Nathan Baltzell >>> Sent: Tuesday, June 09, 2015 6:26 AM >>> To: hps-software >>> Subject: Re: pass1 >>> >>> Hello All, >>> >>> Pass1 started with the calibration runs last night. Documentation is going here: >>> >>> https://confluence.slac.stanford.edu/display/hpsg/2015+EngRun+Reconstr >>> uction+Passes >>> >>> I'm seeing smaller output LCIO files than pass0, by a factor of 2 or more. >>> Anyone know if this is expected? >>> >>> I set one canonical run, 5772, whose LCIO and DST outputs will be going to disk in addition to tape. >>> Any more? (Calibration runs' outputs are going to disk too). >>> >>> -Nathan >>> >>> >>> On Jun 8, 2015, at 21:14, Graham, Mathew Thomas <[log in to unmask]> wrote: >>> >>>> We are ready and the release is 3.3.2-1 here: >>>> >>>> http://srs.slac.stanford.edu/nexus/service/local/artifact/maven/redir >>>> e >>>> ct?r=lcsim-maven2-releases&g=org.hps&a=hps-distribution&v=3.3.2-1&e=j >>>> a >>>> r&c=bin >>>> >>>> >>>>> On Jun 8, 2015, at 6:07 PM, Nathan Baltzell <[log in to unmask]> wrote: >>>>> >>>>> Hi Everyone, >>>>> >>>>> There was discussion late last week that concluded we weren't ready for pass1. >>>>> That included some idea that there was progress to be made on data >>>>> and simulations in order to have some commensurate set. So, are we >>>>> now ready? Should we start >>>>> pass1 or wait? >>>>> >>>>> -Nathan >>>>> >>>>> #################################################################### >>>>> # >>>>> ### >>>>> Use REPLY-ALL to reply to list >>>>> >>>>> To unsubscribe from the HPS-SOFTWARE list, click the following link: >>>>> https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A= >>>>> 1 >>>> >>> >>> ###################################################################### >>> ## >>> Use REPLY-ALL to reply to list >>> >>> To unsubscribe from the HPS-SOFTWARE list, click the following link: >>> https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1 >> > > ######################################################################## > Use REPLY-ALL to reply to list > > To unsubscribe from the HPS-SOFTWARE list, click the following link: > https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1 ######################################################################## Use REPLY-ALL to reply to list To unsubscribe from the HPS-SOFTWARE list, click the following link: https://listserv.slac.stanford.edu/cgi-bin/wa?SUBED1=HPS-SOFTWARE&A=1